Oldedays Classic Car Parts

A pair of side motor mount Brackets only for 1949 to 1954 Chevy passenger cars to mount V-8 engines. SBC or BBC. Will not work with stock steering. you must change to a mustang II front end.

A pair of side motor mount Brackets for 1949 to 1954 Chevy passenger cars to mount V-8 engines. SBC or BBC. Will not work with stock steering. you must change to a mustang II front end. Comes with Hardware and motor rubber mounts.

This die-cut pad is made of the highest quality materials and fit like the original. A new firewall pad has a real effect on engine noise and heat.

New reproduction. heavy duty. Nice unit. This is for 1955 and 1956 AND 1957 Chevys with a SMALL OR BIG Block V-8. Where you want the radiator to Mount in the 6 Cylinder Position. All of the radiators have the automatic trans coolers.

Aluminum downflow radiator feature fully wielded construction and dual 1" tubes. These radiators DO have the transmission cooler. FOR SMALL OR BIG BLOCKS THAT NEED THE RADIATOR TO MOUNT in the 6 CYLINDER position.

This kit comes with the bracket to firewall,7" Dual Diaphragm booster, the master cylinder and proportioning valve. Instructions included. All new parts, made in the USA. we have for both the Disc/Drum (60/40) and for the Disc/Disc (50/50). let us know which one you want.

New. This one is for mounting your engine 3/4" forward, and a TWO piece frame (Weld seam on top of frame). Made in the USA. Comes with hardware to bolt in or you can weld them in.

New. This one is for mounting your engine 3/4" forward, and a ONE piece frame (NO Weld seam on top of frame). Made in the USA. Comes with hardware to bolt in or you can weld them in.

New. This one is for the stock location and for a TWO piece (Welded - with seam) frame. Made in the USA. Comes with hardware to bolt in or you can weld them in. These fit Chevy Small Blocks (can use either stock position or 3/4 forward).

New. These are for our 1955 to 1957 Chevy Side Motor Mount Brackets. you are ordering ONE PAIR.

New Hood Hinges (you are purchasing one pair). Replace those worn and loose hinges on your 1955 or 1956 chevy with these Nice and New ones. We also have the Hood Springs as well if you need them let us know.

New reproduction. heavy duty. Nice unit. This is for 1955, 1956 and 1957 Chevys with a Small Block V-8. Mounts in the Stock Position. All of the radiators have the automatic trans coolers.

New. Set includes rubbers, washers, shaft and nuts; all the parts you need to replace ONE side. NOTE: TWO sets are needed per car. For Small Block V-8 Engines, Original Front Mount positions only.

THESE ARE MADE FROM PRE-POLISHED STAINLESS STEEL, laser cut and very nice. Fit between the radiator and Core Supports. Allows you to mount a 6 cylinder Radiator to a V-8 Core Support OR a V-8 Radiator to a 6 Cylinder core Support.

Made in the USA. Laser cut 16 gauge metal; fit very good and do not have all the holes that the factory ones have for the voltage regulator and horn relay. Also do not have the ribs.

1955-1956 Chevy Hood Hinge Hardware Kit - Stainless Steel. Replace your worn out, rusty old harware with these new stainless steel set. We also have the Hood Hinges as well (EC0014)

Aluminum downflow radiator feature fully wielded construction and dual 1" tubes. These radiators DO have the transmission cooler. 6-CYLINDER.

Aluminum downflow radiator feature fully wielded construction and dual 1" tubes. These radiators DO have the transmission cooler. V-8 in the STOCK position.

This Bracket set is for LS1 to Factory small block chevy 1955, 1956 or 1957 passenger car.

This die-cut pad is made of the highest quality materials and fit like the original. A new firewall pad has a real effect on engine noise and heat.

New reproduction. heavy duty. Nice unit. in the 6 cylinder position, All of the radiators have the automatic trans coolers. Brass/Copper

This die-cut pad is made of the highest quality materials and fit like the original. A new firewall pad has a real effect on engine noise and heat.

This set has the two Grille Bar support brackets as well as the Hood Latch Support Bracket. All is made from Stainless Steel. Nice stuff!

These reproductions are like the NOS originals, but with the clip that replaced the capillary tube.

1957 Chevy Hood Hinge Hardware Kit - Stainless Steel. Replace your worn out and rusty old set with these new stainless steel set. We also have the hood hinges and springs.

New Stainless Steel Hood Hinges (you are purchasing one pair). Replace those worn and loose hinges on your 1957 Chevy with these Nice and New ones. We also have the Hood Springs and Hardware kit as well if you need them let us know.

Laser cut of polished stainless; very nice. They are polished on the side that shows next to the radiator front. Comes just like the photo shows

These are new brackets, never installed. These mounts are the ones you need to make the new engine fit nice and trans needs for extra support. Made in the USA. Comes with bolts and instructions. Front Mount Type.

New. This one is for the stock location and for a ONE piece (seamless) frame. Made in the USA. Comes with hardware to bolt in or you can weld them in. These fit Chevy Small Blocks (can use either stock position or 3/4 forward).

Made in the USA. Laser cut 16 gauge metal; fit very good and do not have all the holes that the factory ones have for the voltage regulator and horn relay. Also do not have the ribs.

1958-64 Chevrolet passenger car 605 power steering bracket to install power steering.

These brackets are for the short water pump (note- short water pump only) Can be used with headers or with stock manifolds. Any questions please e-mail us. These brackets are lazer cut, grade 8 bolts.

Fits all Big Block Chevy 396, 402, 427, 454, and 502 using short water pump only Lazer cut out of mild steel all grade 8 bolts/hardware very nice. Will also work for 671 or 871 setup.

Fits all Big Block Chevy 396,402,427,454, and 502 using short water pump only. Lazer cut out of mild steel, grade 8 bolts/hardware very nice.

Fits all Big Block Chevy Chevrolet 396, 402, 427, 454, and 502 using short water pump only. Mounts on the passenger side. These are Lazer cut out of mild steel, all grade 8 bolts and hardware very nice. Also works for 671 or 871.

Genuine Chevy Brackets - Never used. These brackets are for the long water pump. For 396, 454 and 502.

Genuinee Chevrolet Brackets - Never Used. These brackets are for long water pump - 396, 454, 502.

This kit comes with the bracket to mount it any where you want. Electic pump with instructions.

This kit comes with the bracket to mount it any where you want. Electic pump with instructions

Lazer Cut, grade 8 bolts and work with short water pump only. They work with no holes in the end of the cylinder head.

These brackets are lazer cut, grade 8 bolts. Works with short water pump only.

These brackets are laser cut, grade 8 bolts. Works with short water pump only.

Small block Chevy starter support, stainless steel. Fits on the side of the block and the front of the starter. Made in the USA.

Universal, will work with long or short water pump, with high or low mount, early or late pumps. Come with grade 8 bolts. COME WITH BRACKETS AND BOLTS ONLY. Will NOT work with metric pumps.