Oldedays Classic Car Parts

All GM 10-12 bolt rear disc brake brackets set. New, never installed. Made in the USA. Comes with hardware and instructions for the items to use.

Use with 1980-1985 Cadillac Seville rear callipers and 1979 Trans Am rear rotors.

A pair of side motor mount Brackets only for 1949 to 1954 Chevy passenger cars to mount V-8 engines. SBC or BBC. Will not work with stock steering. you must change to a mustang II front end.

A pair of side motor mount Brackets for 1949 to 1954 Chevy passenger cars to mount V-8 engines. SBC or BBC. Will not work with stock steering. you must change to a mustang II front end. Comes with Hardware and motor rubber mounts.

New. This one is for mounting your engine 3/4" forward, and a TWO piece frame (Weld seam on top of frame). Made in the USA. Comes with hardware to bolt in or you can weld them in.

New. This one is for mounting your engine 3/4" forward, and a ONE piece frame (NO Weld seam on top of frame). Made in the USA. Comes with hardware to bolt in or you can weld them in.

New. This one is for the stock location and for a TWO piece (Welded - with seam) frame. Made in the USA. Comes with hardware to bolt in or you can weld them in. These fit Chevy Small Blocks (can use either stock position or 3/4 forward).

FOR 1941 TO 1954 FULL SIZE CHEVROLET PASSENGER CARS AND 1937 TO 1955 1ST SERIES CHEVY/GMC PICKUP TRUCKS. FOR 6 CYLINDER ENGINES ONLY.

New. Set includes rubbers, washers, shaft and nuts; all the parts you need to replace ONE side. NOTE: TWO sets are needed per car. For Small Block V-8 Engines, Original Front Mount positions only.

1955, 1956, 1957 CHEVROLET NOMAD, WAGON TAILGATE CABLE RETRACTOR BRACKETS, PAIR, STAINLESS STEEL NEW REPRODUCTION, VERY NICE.

FOR 1955 TO 1962 FULL SIZE CHEVROLET PASSENGER CARS AND 1955 TO 1962 CHEVY/GMC PICKUP TRUCKS. FOR 6 CYLINDER ENGINES ONLY.

Made in the USA. This is made from Stainless Steel. You are buying one each. This is for 1955 and 1956 Chevy Passenger Cars.

New, Made in USA. Use this to put a T-350 or T-400 Transmission in your 1955-1956 265 V-8 and to continue to use the stock starter. Requires 168 tooth flex plate.

This Bracket set is for LS1 to Factory small block chevy 1955, 1956 or 1957 passenger car.

Made in the USA. This is made from Stainless Steel. You are buying one each. This is for 1957 Chevy Passenger Cars.

1955, 1956 and 1957 CHEVROLET PASSENGER CAR 605 POWER STEERING BRACKET TO INSTALL 605 POWER STEERING. Comes with instructions.

Complete Lower Unit. The tubular brackets are black semi gloss powered coated. The tubular cross member unit are made in the USA and easy to install. All new parts except the "re manufactured racks".

The tubular brackets will be black semi gloss powered coated. These units are made in the USA and are easy to install. All new parts. Comes with the mounting brackets with bolts.

To mount the UPPER shock to instead of using the floor. NOT for NOMADS or Station Wagons. NOTE: These are now Powder Coated, Black Semi Gloss, Looks great.

New. Made in USA. You can bolt it in or weld the side brackets to your frame. Very nice unit. Comes with hardware and instructions.

Rear lower shock u-bolt plates below the rear springs. New mild steel.

New. This one is for the stock location and for a ONE piece (seamless) frame. Made in the USA. Comes with hardware to bolt in or you can weld them in. These fit Chevy Small Blocks (can use either stock position or 3/4 forward).

All new setup, works great. Adjustable, no welding, grade 8 bolts and mild steel. Made in the USA.

New. These are the best traction bars made today in the USA. Just bolt on and go.

New. These mounts are the ones you need to make the new engine fit nice and the transmission needs for the extra support. Made in the USA. With bolts and instructions.

Out front, this is the part that takes the first bump! If yours has been straightened one time too many, start fresh with one of these stamped brackets. Painted in durable black.

Out front, this is the part that takes the first bump! If yours has been straightened one time too many, start fresh with one of these stamped brackets. Painted in durable black.

FITS CHEVROLET CHEVY Blazer, Suburban, and 10/12 bolt Pickup rear ends. New. MADE IN USA. Very nice setup. Comes with hardware and instructions for the items to use.

Small block Chevy starter support, stainless steel. Fits on the side of the block and the front of the starter. Made in the USA.

These seat brackety retainers are for 55-56-57 passenger cars. They are made of stainless steel. pair

These are new brackets, never installed. These mounts are the ones you need to make the new engine fit nice and trans needs for extra support. Made in the USA. Comes with bolts and instructions. Front Mount Type.

This Sway Bar Bracket fits the Tubular A Arms we sell. You will need to drill 1 hole each side. Easy to install and works good. We also sell Sway Bars.

The standard bracket is semi-gloss powder coated. Easy to install, all new parts.

New. Front Disc Brake Brackets. MADE IN USA. Very nice setup. Comes with hardware and instructions for the items to use. We also have the other items you will need. You will need to use: eleven inch rotors from 1969 - 1972 Chevelle. Calipers from 1979 - 1985 Monte Carlo.

Fits 1955-1960. New item, never been installed. Made in the USA. Very nice set-up. Comes with hardware and instructions for the items to use.

1958-64 Chevrolet passenger car 605 power steering bracket to install power steering.

New, never installed. Made in the USA. Very nice set-up. Comes with hardware and instructions for the items to use.

Fits 1965-1968 Impala Front. New item, never been installed. Made in the USA. Very nice set-up. Comes with hardware and instructions for the items to use.

These brackets are for the short water pump (note- short water pump only) Can be used with headers or with stock manifolds. Any questions please e-mail us. These brackets are lazer cut, grade 8 bolts.

Genuine Chevy Brackets - Never used. These brackets are for the long water pump. For 396, 454 and 502.

Genuinee Chevrolet Brackets - Never Used. These brackets are for long water pump - 396, 454, 502.

Lazer Cut, grade 8 bolts and work with short water pump only. They work with no holes in the end of the cylinder head.

Universal, will work with long or short water pump, with high or low mount, early or late pumps. Come with grade 8 bolts. COME WITH BRACKETS AND BOLTS ONLY. Will NOT work with metric pumps.

FITS FORD 8" OR 9", REAR DISC BRAKE SET UP that have the same Backing Plate Spacer measurements as in our photo. the Bolt Holes are for 3/8" bolts.

FITS ALL FORD 9" BIG BEARING (NOT NEW BEARING)REAR DISC BRAKE SET UP. BIG WHEEL BEARING. PLEASE NOTE MEASUREMENTS OF THE BACKING PLATE SPACER IN PHOTO. THE BOLT HOLES ARE FOR 1/2" BOLTS.

FITS ALL FORD 9" REAR DISC BRAKE SET UP. SMALL WHEEL BEARING. PLEASE NOTE MEASUREMENTS OF THE BACKING PLATE SPACER IN PHOTO. BOLT HOLES ARE FOR 3/8" BOLTS. IF UNSURE PLEASE CALL BEFORE ORDERING.

Fits all Big Block Chevy 396, 402, 427, 454, and 502 using short water pump only Lazer cut out of mild steel all grade 8 bolts/hardware very nice. Will also work for 671 or 871 setup.

Fits all Big Block Chevy 396,402,427,454, and 502 using short water pump only. Lazer cut out of mild steel, grade 8 bolts/hardware very nice.

Fits all Big Block Chevy Chevrolet 396, 402, 427, 454, and 502 using short water pump only. Mounts on the passenger side. These are Lazer cut out of mild steel, all grade 8 bolts and hardware very nice. Also works for 671 or 871.

These brackets are laser cut, grade 8 bolts. Works with short water pump only.

These brackets are lazer cut, grade 8 bolts. Works with short water pump only.